Biomechanical behavior of different designs of hybrid abutment-restoration on the posterior crown: a finite element analysis.

This study aimed to evaluate the influence of material and crown design on the biomechanical behavior of implant-supported crowns with hybrid abutment (HA) through three-dimensional (3D) finite element analysis. The study factors were the type of material used as the mesostructure or crown (zirconia, lithium disilicate, and hybrid ceramic) and the crown design cemented to the titanium base (mesostructure cemented to the titanium base and a crown cemented on it (HaC); hybrid crown-abutment, the abutment and crown are manufactured as a single piece and cemented to the titanium base (HC); monolithic crown cemented on the titanium base and screwed to the implant (CS); and monolithic crown cemented on the titanium base (CC). Four 3D models were constructed using an implant with an internal connection, and an oblique load of 130 N was applied at 45° to the long axis of the implant. The models were evaluated using the von Mises stress for crown, abutment, screw, and implant and maximum principal stress for bone tissues. The lowest stresses occurred in the groups with a lower elastic modulus material, mainly hybrid ceramics, considered a material with greater resilience. The cemented crown group presented the lowest stress values. The stresses were concentrated in the cervical region of the crown at the titanium crown/base interface. Mesostructures made of materials with a higher elastic modulus exhibited a higher concentration of stress. The presence of a screw hole increased the stress concentration in the ceramic crown. Cemented ceramic crowns exhibited better biomechanical behavior than screw-retained crowns.

In Vitro Impact of Fluconazole on Oral Microbial Communities, Bacterial Growth, and Biofilm Formation.

Antifungal agents are widely used to specifically eliminate infections by fungal pathogens. However, the specificity of antifungal agents has been challenged by a few studies demonstrating antibacterial inhibitory effects against Mycobacteria and Streptomyces species. Here, we evaluated for the first time the potential effect of fluconazole, the most clinically used antifungal agent, on a human oral microbiota biofilm model. The results showed that biofilm viability on blood and mitis salivarius agar media was increased over time in the presence of fluconazole at clinically relevant concentrations, despite a reduction in biomass. Targeted PCR revealed a higher abundance of Veillonella atypica, Veillonella dispar, and Lactobacillus spp. in the fluconazole-treated samples compared to the control, while Fusobacterium nucleatum was reduced and Streptococcus spp were not significantly affected. Further, we tested the potential impact of fluconazole using single-species models. Our results, using Streptococcus mutans and Streptococcus mitis luciferase reporters, showed that S. mutans planktonic growth was not significantly affected by fluconazole, whereas for S. mitis, planktonic growth, but not biofilm viability, was inhibited at the highest concentration. Fluconazole's effects on S. mitis biofilm biomass were concentration and time dependent. Exposure for 48 h to the highest concentration of fluconazole was associated with S. mitis biofilms with the most increased biomass. Potential growth inhibitory effects were further tested using four non-streptococcal species. Among these, the planktonic growth of both Escherichia coli and Granulicatella adiacens was inhibited by fluconazole. The data indicate bacterial responses to fluconazole that extend to a broader range of bacterial species than previously anticipated from the literature, with the potential to disturb biofilm communities.

Biomechanical behavior of different designs of hybrid abutment-restoration on the posterior crown: a finite element analysis

Abstract This study aimed to evaluate the influence of material and crown design on the biomechanical behavior of implant-supported crowns with hybrid abutment (HA) through three-dimensional (3D) finite element analysis. The study factors were the type of material used as the mesostructure or crown (zirconia, lithium disilicate, and hybrid ceramic) and the crown design cemented to the titanium base (mesostructure cemented to the titanium base and a crown cemented on it (HaC); hybrid crown-abutment, the abutment and crown are manufactured as a single piece and cemented to the titanium base (HC); monolithic crown cemented on the titanium base and screwed to the implant (CS); and monolithic crown cemented on the titanium base (CC). Four 3D models were constructed using an implant with an internal connection, and an oblique load of 130 N was applied at 45° to the long axis of the implant. The models were evaluated using the von Mises stress for crown, abutment, screw, and implant and maximum principal stress for bone tissues. The lowest stresses occurred in the groups with a lower elastic modulus material, mainly hybrid ceramics, considered a material with greater resilience. The cemented crown group presented the lowest stress values. The stresses were concentrated in the cervical region of the crown at the titanium crown/base interface. Mesostructures made of materials with a higher elastic modulus exhibited a higher concentration of stress. The presence of a screw hole increased the stress concentration in the ceramic crown. Cemented ceramic crowns exhibited better biomechanical behavior than screw-retained crowns.

Resumo O estudo teve como objetivo avaliar a influência do material e do desenho da coroa no comportamento biomecânico de coroas implanto-suportadas com pilar híbrido (AH) por meio da análise tridimensional (3D) de elementos finitos. Os fatores de estudo foram o tipo de material do HA ou coroa (zircônia, dissilicato de lítio e cerâmica híbrida) e o desenho da coroa sobre a base de titânio (mesoestrutura cimentada à base de titânio e coroa total cimentada em cerâmica; pilar e coroa fabricados em peça única cimentada à base de titânio; coroa monolítica cimentada sobre a base de titânio e aparafusada ao implante; e coroa monolítica cimentada à base de titânio). Quatro modelos 3D foram construídos e uma carga oblíqua de 130 N foi aplicada a 45° em relação ao longo eixo do dente. Os modelos foram avaliados utilizando a tensão de von Mises para a coroa, pilar, parafuso, implante e tensão principal máxima (tensão de tração) para o tecido ósseo. As menores tensões ocorreram nos grupos que apresentaram um material com menor módulo de elasticidade, principalmente a cerâmica híbrida, considerada um material com maior resiliência. Com relação às diferentes configurações, o modelo com coroa cimentada apresentou os menores valores de tensão. As tensões foram concentradas na região cervical da coroa na interface entre coroa e base de titânio. Mesoestruturas feitas de materiais com maior módulo de elasticidade exibiram maior concentração de tensões. A presença de um orifício para parafuso aumentou a concentração de tensão na coroa de cerâmica. As coroas cerâmicas cimentadas exibiram melhor comportamento biomecânico do que as coroas parafusadas.

Demystifying interactions between micro organisms in oral candidiasis biofilm: the key to enhancing treatments

Introduction: candida albicans is a fungal pathogen that can provoke diseases ranging from oral infections to life-threatening systemic disorders. It is now recognized that oral bacteria, such as the genus Streptococcus, establish synergistic relationships with C. albicans, which could potentially increase the fungi's virulence and pathogenicity. Objective: this narrative review aimed to discuss the Candida-Streptococcus mechanisms of interactions and their contribution to increasing oral candidiasis severity. In addition, it provides a background of biofilm formation and potential therapeutical targets. Sources of Data: searches for papers in English were performed in the Pubmed database until May 2022. MeSH and free terms related to the field were used. In vitro studies were selected, tabulated, and qualitative and quantitative data were analyzed descriptively. Synthesis of Data: among the early colonizers bacteria, evidence pointed out that S. gordonnii and S. oralis have major implications in oral candidiasis, in which mixed biofilms increase the infection severity and challenge the host's defense. On the other hand, the outcomes of the interaction between C. albicans and S. mitis, S. sanguinis, or S. mutans remain little explored in the oral candidiasis scenario, albeit evidence pointed out an enhanced fungus population and virulence factors. Conclusion: overall, considering the polymicrobial profile of the infection and the potential to increase Candida-related disease severity, therapeutical strategies should also consider bacteria management.

Introdução: candida albicans é um patógeno fúngico que pode provocar doenças que variam de infecções orais a distúrbios sistêmicos com risco de vida. Hoje se reconhece que as bactérias orais, como o gênero Streptococcus, estabelecem relações sinérgicas com C. albicans, o que pode potencialmente aumentar a virulência e patogenicidade do fungo. Objetivo: esta revisão narrativa teve como objetivo discutir os mecanismos de interação Candida-Streptococcus e sua contribuição para o agravamento da candidíase oral. Além disso, fornece uma breve explanação sobre a formação do biofilme e potenciais alvos terapêuticos. Fonte dos dados: foi realizada pesquisa na base de dados Pubmed para a busca de artigos publicados em Inglês até maio de 2022. Para isso, foram utilizados descritores relacionados ao tema. Estudos in vitro foram selecionados, tabulados e seus resultados quantitativos e qualitativos analisados descritivamente. Síntese dos dados: entre as bactérias denominadas colonizadores iniciais, evidências apontam que S. gordonnii e S. oralis têm implicações importantes na candidíase oral, na qual biofilmes mistos aumentam a gravidade da infecção e desafiam a defesa do hospedeiro. Por outro lado, os desfechos das interações entre C. albicans e S. mitis, S. sanguinis ou S. mutans permanecem pouco explorados no cenário da candidíase oral, apesar de evidências apontarem um aumento dapopulação fúngica e de fatores de virulência. Conclusão: de maneira geral, considerando o perfil polimicrobiano da infecção e o potencial agravamento das doenças provocadas por Candida spp, as estratégias terapêuticas não devem estar focadas apenas no fungo, mas também devem considerar o manejo da bactéria.

Different Treatment Modalities Using Dental Implants in the Posterior Maxilla: A Finite Element Analysis.

The objective of this study was to compare the biomechanical behavior of peri-implant bone tissue and prosthetic components in two modalities of treatment for posterior region of the maxilla, using short implants or standard-length implants associated with bone graft in the maxillary sinus. Four 3D models of a crown supported by an implant fixed in the posterior maxilla were constructed. The type of implant: short implant (S) or standard-length implant with the presence of sinus graft (L) and type of crown retention: cemented (C) or screwed (S) were the study factors. The models were divided into SC- cemented crown on a short implant; SS- screwed crown on the short implant; LC- cemented crown on a standard-length implant after bone graft in the maxillary sinus and LS- crown screwed on a standard-length implant after bone graft in the maxillary sinus. An axial occlusal loading of 300 N was applied, divided into five points (60N each) corresponding to occlusal contact. The following analysis criteria were observed: Shear Stress, Maximum and Minimum Main Stress for bone tissue and von Mises Stress for the implant and prosthetic components. The use of standard-length implants reduced the shear stress in the cortical bone by 35.75% and the medullary bone by 51% when compared to short implants. The length of the implant did not affect the stress concentration in the crown, and the cement layer acted by reducing the stresses in the ceramic veneer and framework by 42%. Standard-implants associated with cemented crowns showed better biomechanical behavior.

Topography of Primary Molar Pulp Chamber Floor: A Scanning Electron Microscopy and Micro-Computed Tomography Analysis

ABSTRACT Objective: To determine in vitro the frequency, shape, type, diameter, and patency of accessory canals in the primary molars pulp chamber floor. Material and Methods: Sixteen healthy primary molars were evaluated by micro-computed tomography and scanning electron microscopy. Descriptive analyses of the frequency, shape (round, oval, or irregular), type (blind, true, or hidden), patency and diameter of the accessory canals were performed. Results: Half of the teeth presented accessory canals, 62.5% of which were located in the upper molars and 37.5% in the lower molars. The most frequent shape was irregular. In three-dimensional analysis, blind accessory canals (12.5%) and with patency (18.7%) of the teeth were observed. The average accessory canal diameter was 51.97 µm (± 26.03 µm). Conclusion: Upper molars showed a higher frequency of accessory canals with larger diameters. The irregular shape was the most frequent. 18.7% of accessory channels showed patency.

Botulinum toxin type A applications for masticatory myofascial pain and trigeminal neuralgia: what is the evidence regarding adverse effects?

OBJECTIVES: The objective of the study was to conduct a systematic review of literature assessing botulinum toxin type A (BoNT-A) safety and adverse effects in the treatment of myofascial pain (MFP) and trigeminal neuralgia (TN). MATERIALS AND METHODS: The search for articles by two specific researchers involved the PubMed, EMBASE, Web of Science, and Scopus databases. Specific terms were used, and no publication time and language restrictions were applied. Clinical trials that investigated the effects of BoNT-A among participants with myofascial pain in masticatory muscles or trigeminal neuralgia were considered eligible for this systematic review. Data for each study were extracted and analyzed according to a PICO-like structured reading. RESULTS: The search strategy provided 436 citations. After analysis, 16 citations were included, seven for MFP and nine for TN. In all studies, BoNT-A was well tolerated and improved pain. The most common adverse effects were temporary regional weakness, tenderness over the injection sites, and minor discomfort during chewing. Most studies reported a spontaneous resolution of adverse effect. CONCLUSIONS: It can be concluded that BoNT-A treatment is well tolerated, since minor adverse effects were the most frequently reported; however, it is recommended that future studies aim to assess the safety and possible adverse effects of multiples applications or high doses of this treatment. CLINICAL RELEVANCE: BoNT-A has been increasingly diffused in dentistry, being used for the management of masticatory myofascial pain and trigeminal neuralgia. Nonetheless, there is no consensus about its efficacy and adverse effects that could occur when this treatment is applied.

Influence of Abutment Collar Height and Implant Length on Stress Distribution in Single Crowns.

This in silico study evaluated the influence of the abutment collar height and implants length on the biomechanical behavior of morse taper single dental implants with different crown-to-implant ratio. Six virtual models were constructed (S11, M11, L11, S13, M13 and L13) by combining short (S: 2.5 mm), medium (M: 3.5 mm) or long (L: 4.5 mm) abutment collar heights with different implant lengths (11 or 13-mm). An upper central incisor of 11-mm height was constructed on top of each abutment. Each set was positioned in a virtual bone model and exported to analyze mathematically. A 0.60-mm mesh was created after convergence analysis and a 49 N load was applied to the cingulum of the crown at an angle of 45°. Load-generated stress distribution was analyzed in the prosthetic components according to von Mises stress criteria (σvM) and in the cortical and cancellous bone by means of shear stress (εmax). The use of longer collar abutments (L11) increased the stress on the abutment by 250% and resulted in 40% higher stresses on the screw and 92% higher cortical shear stresses compared to short collared abutments (S11). Increasing the implant length produced a slight stress reduction on cortical bone. Cancellous bone was not affected by the crown-to-implant ratio. Longer abutment collars concentrate stresses at the implant level and cortical bone by increasing the crown-to-implant ratio.

Influence of abutment collar height and implant length on stress distribution in single crowns

Abstract This in silico study evaluated the influence of the abutment collar height and implants length on the biomechanical behavior of morse taper single dental implants with different crown-to-implant ratio. Six virtual models were constructed (S11, M11, L11, S13, M13 and L13) by combining short (S: 2.5 mm), medium (M: 3.5 mm) or long (L: 4.5 mm) abutment collar heights with different implant lengths (11 or 13-mm). An upper central incisor of 11-mm height was constructed on top of each abutment. Each set was positioned in a virtual bone model and exported to analyze mathematically. A 0.60-mm mesh was created after convergence analysis and a 49 N load was applied to the cingulum of the crown at an angle of 45°. Load-generated stress distribution was analyzed in the prosthetic components according to von Mises stress criteria (σvM) and in the cortical and cancellous bone by means of shear stress (εmax). The use of longer collar abutments (L11) increased the stress on the abutment by 250% and resulted in 40% higher stresses on the screw and 92% higher cortical shear stresses compared to short collared abutments (S11). Increasing the implant length produced a slight stress reduction on cortical bone. Cancellous bone was not affected by the crown-to-implant ratio. Longer abutment collars concentrate stresses at the implant level and cortical bone by increasing the crown-to-implant ratio.

Resumo Este estudo avaliou a influência da altura da porção transmucosa do pilar protético com junção cone morse e do comprimento dos implantes no comportamento biomecânico coroas unitárias com diferentes proporção coroa-implante. Seis modelos virtuais (S11, M11, L11, S13, M13 e L13) foram construídos combinando pilares protéticos com transmucoso considerado: curto (S: 2,5 mm), médio (M: 3,5 mm) ou longo (L: 4,5 mm) com diferentes comprimentos de implantes (11 ou 13 mm). Um incisivo central superior de 11 mm de altura foi construído para cada pilar. Cada conjunto foi posicionado em um modelo de osso virtual e exportado para análise matemática. Uma malha de 0,60 mm foi criada após análise de convergência e uma carga de 49 N foi aplicada ao cíngulo da coroa em um ângulo de 45°. A distribuição de estresse gerada por carga foi analisada nos componentes protéticos de acordo com o critério de tensão de von Mises (σvM) e no osso cortical e medular por meio da tensão de cisalhamento (εmax). O uso de pilares com porção transmucosa mais longa (L11) aumentou a tensão no pilar protético em 250%, e resultou em tensões 40% maiores no parafuso e 92% no osso cortical em relação aos pilares com transmucoso curto (S11). O aumento do comprimento do implante produziu uma ligeira redução da tensão de cisalhamento no osso cortical. O osso medular não foi afetado pela relação coroa-implante. Pilares protéticos com porção transmucosa mais longa concentram tensões no implante e no osso cortical, quando a proporção coroa-implante é aumentada.

Pro-inflammatory Analysis of Macrophages in Contact with Titanium Particles and Porphyromonas gingivalis.

During insertion of titanium dental implants, particles may shear from the implant to the periimplant region causing osteolysis, and their association with bacteria can exacerbate the inflammatory reaction. However, the association of a high invasive bacterium from the oral cavity, Porphyromonas gingivalis (Pg), and titanium particles remains unknown. This study evaluated pro-inflammatory reaction of human macrophages in contact with micro and nanoparticles of titanium associated with Porphyromonas gingivalis lipopolysaccharide (PgLPS). THP-1 cell were used and treated for 12, 24 and 48 h following 6 groups: Control(C), PgLPS (L); Microparticles (M); Nanoparticles (N); PgLPS and microparticles (LM); PgLPS and nanoparticles (LN). The following assays were carried out: i) cell viability using MTS, ii) cell morphology by SEM and iii) expression of tumor necrosis factor alpha (TNF-α), interleukin-1 beta (IL-1ß) and interleukin-6 (IL-6) by qRT-PCR and ELISA. For statistics two-way ANOVA followed by Tukey's test was used (p<0.05). After treatment, cells presented similar viability and morphology demonstrating that the treatments were not able to induce cell death. Gene expression was significantly higher for TNF-α and IL1-ß after 12 h, and for IL-6 after 24 h in the N and LN groups. Cytokine production over time was an ascending curve for TNF-α with the peak at 48 h and IL1-ß and IL-6 had a straight line among the time points, although cells from N group presented a significant production of IL-6 at 48 h. In conclusion, these results suggest that titanium nanoparticles stimulate stronger pro-inflammatory response in macrophages, independent of their association with LPS from P.gingivalis.

Pro-inflammatory Analysis of Macrophages in Contact with Titanium Particles and Porphyromonas gingivalis

Abstract During insertion of titanium dental implants, particles may shear from the implant to the periimplant region causing osteolysis, and their association with bacteria can exacerbate the inflammatory reaction. However, the association of a high invasive bacterium from the oral cavity, Porphyromonas gingivalis (Pg), and titanium particles remains unknown. This study evaluated pro-inflammatory reaction of human macrophages in contact with micro and nanoparticles of titanium associated with Porphyromonas gingivalis lipopolysaccharide (PgLPS). THP-1 cell were used and treated for 12, 24 and 48 h following 6 groups: Control(C), PgLPS (L); Microparticles (M); Nanoparticles (N); PgLPS and microparticles (LM); PgLPS and nanoparticles (LN). The following assays were carried out: i) cell viability using MTS, ii) cell morphology by SEM and iii) expression of tumor necrosis factor alpha (TNF-α), interleukin-1 beta (IL-1β) and interleukin-6 (IL-6) by qRT-PCR and ELISA. For statistics two-way ANOVA followed by Tukey's test was used (p<0.05). After treatment, cells presented similar viability and morphology demonstrating that the treatments were not able to induce cell death. Gene expression was significantly higher for TNF-α and IL1-β after 12 h, and for IL-6 after 24 h in the N and LN groups. Cytokine production over time was an ascending curve for TNF-α with the peak at 48 h and IL1-β and IL-6 had a straight line among the time points, although cells from N group presented a significant production of IL-6 at 48 h. In conclusion, these results suggest that titanium nanoparticles stimulate stronger pro-inflammatory response in macrophages, independent of their association with LPS from P.gingivalis.

Resumo Durante a inserção de implantes dentários partículas de titânio podem ser liberadas na região peri-implantar levando ao processo de osteólise e a associação com a bactéria pode exacerbar ainda mais a reação inflamatória. Entretanto, a associação de uma bactéria altamente invasiva da cavidade oral, Porphyromonas gingivalis (Pg) e partículas de titânio ainda não foi investigada. Este estudo avaliou a reação pró-inflamatória de macrófagos humanos em contato com micro e nanopartículas de titânio associada a lipopolissacarídeo P. gingivalis (PgLPS). As células THP-1 foram utilizadas e tratadas durante 12, 24 e 48 h nos 6 seguintes grupos: Controle (C), PgLPS (L); micropartículas (M); nanopartículas (N); PgLPS e micropartículas (LM); PgLPS e nanopartículas (LN). Em seguida foram realizados os seguintes ensaios: i) a viabilidade celular utilizando MTS, ii) a morfologia celular por MEV e iii) expressão do fator de necrose tumoral alfa (TNF-α), interleucina-1 beta (IL-1β) e interleucina 6 (IL-6) por qRT-PCR e ELISA. Como estatística foi realizado o teste ANOVA two-way seguido pelo teste de Tukey (p<0,05). Após o tratamento, as células apresentaram viabilidade e morfologia semelhantes, demonstrando que os tratamentos não foram capazes de induzir a morte celular. A expressão de genes foi significativamente mais elevada para o TNF-α e IL1-β após 12h, e para a IL-6 após 24 horas em N e grupos de LN. A produção de citocinas em relação ao tempo representou uma curva ascendente para o TNF-α com o pico em 48 h, enquanto que para IL1-β e IL-6 se apresentou como uma linha reta com relação ao tempo, exceto pelo grupo N que foi significativo para IL-6 em 48 h . Conclui-se, a partir destes resultados, que as nanopartículas de titânio produziram o maior estímulo na resposta pró-inflamatória nos macrófagos, independente da sua associação com LPS de P. gingivalis.

Flexible resins: an esthetic option for partially edentulous patients / Resinas flexíveis: uma opção estética para desdentados parciais

Flexible thermoplastic resins have been used as an alternative to partially edentulous patients for decades in the USA. However, they are neither popular nor widespread in Brazil. This material represents an excellent treatment option to solve clinical problems such as compromised esthetics caused by visible metal clasps, and fall fracture of dentures made of conventional resins. Additionally, there is little researching and no controlled clinical studies about the use of flexible resins in prosthodontics. For these reasons, this study presents a case report of a dissatisfied patient treated with a conventional removable partial denture, which was replaced by a modified metal framework without metal clasps in combination with flexible resin, and a literature review about this material focusing on the dental practitioner. The study also reports how these polymers can be used, their indications, and their clinical and laboratory considerations.

As resinas termoplásticas flexíveis têm sido uma alternativa para tratamento de pacientes parcialmente desdentados disponível há décadas nos EUA. No Brasil, no entanto, ainda são pouco utilizadas e conhecidas. Este material pode representar uma excelente opção de tratamento reabilitador, para solucionar problemas tais como o aparecimento de grampos metálicos com comprometimento da estética e fratura de próteses confeccionadas com resinas convencionais devido a quedas. Além disso, pesquisas acerca desse material são escassas e não há estudos clínicos de sua utilização na área de prótese dentária na literatura. Por essas razões, este estudo apresenta um caso clínico de uma paciente insatisfeita tratada com prótese removível convencional, a qual foi substituída por uma estrutura metálica modificada sem grampos em combinação com resina, e uma revisão da literatura, com o objetivo de elaborar um apanhado de informações para o clínico sobre estes materiais, além de apresentar como estes polímeros podem ser utilizados, as suas indicações em prótese parcial removível, suas considerações clínicas e laboratoriais.

Recolonization of Mutans Streptococci after Application of Chlorhexidine Gel

Streptococcus mutans is specifically suppressed by intensive treatment with chlorhexidine gel, but the time for recolonization and the effect on other oral bacteria are not totally clear. In this study, recolonization of mutans streptococci was evaluated in nine healthy adult volunteers, who were highly colonized with this microorganism. Stimulated saliva was collected before (baseline) and at 1, 7, 14, 21 and 28 days after application of 1% chlorhexidine gel on volunteers' teeth for two consecutive days. On each day, the gel was applied using disposable trays for 3 x 5 min with intervals of 5 min between each application. Saliva was plated on blood agar to determine total microorganisms (TM); on mitis salivarius agar to determine total streptococci (TS) and on mitis salivarius agar plus bacitracin to determine mutans streptococci (MS). Chlorhexidine was capable of reducing the counts of MS and the proportion of MS with regard to total microorganisms (%MS/TM) (p<0.05), but these values did not differ statistically from baseline (p>0.05) after 14 days for MS and 21 days for %MS/TM. The counts of TM and TS and the proportion of MS to total streptococci did not differ statistically from baseline (p>0.05) after chlorhexidine treatment. The results suggest that the effect of chlorhexidine gel treatment on suppression of mutans streptococci is limited to less than a month in highly colonized individuals.

Streptococcus mutans é especificamente suprimido pelo tratamento intensivo com clorexidina em gel, mas o tempo de recolonização e o efeito em outras bactérias orais não está totalmente claro. Nesse estudo, a recolonização de estreptococos do grupo mutans foi avaliado em nove voluntários adultos saudáveis, os quais eram altamente colonizados por esse microrganismo. Saliva estimulada foi coletada antes (baseline) e 1, 7, 14, 21 e 28 dias após a aplicação de clorexidina em gel a 1% nos dentes dos voluntários por dois dias consecutivos. Em cada dia, o gel foi aplicado utilizando moldeiras descartáveis por 3 x 5 min com intervalos de 5 min entre cada aplicação. A saliva foi inoculada em ágar sangue para determinação dos microrganismos totais (MT); em mitis salivarius ágar para determinação dos estreptococos totais (ET) e em meio mitis salivarius com bacitracina para determinar a contagem de estreptococos do grupo mutans (EGM). O tratamento com clorexidina foi capaz de reduzir as contagens de EGM e a proporção de EGM em relação aos microrganismos totais (%EGM/MT) (p<0,05), mas esses valores não diferiram estatisticamente do baseline (p>0,05) após 14 dias para EGM e 21 dias para %EGM/MT. As contagens de MT e ET e a proporção de EGM em relação a estreptococos totais não difereriram estatisticamente do baseline (p>0,05) após o tratamento com clorexidina. Os resultados sugerem que o efeito do tratamento com clorexidina em gel na supressão de estreptococos do grupo mutans é limitado a menos de um mês em indivíduos altamente colonizados. .

Direct adhesive pin-retained restorations for severely worn dentition treatment: a 1.5-year follow-up report.

Excessive occlusal surface wear can result in occlusal disharmony, functional and esthetic impairment. As a therapeutic approach, conventional single crowns have been proposed, but this kind of treatment is complex, highly invasive and expensive. This case report describes the clinical outcomes of an alternative minimally invasive treatment based on direct adhesive-pin retained restorations. A 64-year-old woman with severely worn dentition, eating problems related to missing teeth and generalized tooth hypersensitivity was referred for treatment. Proper treatment planning based on the diagnostic wax-up simulation was used to guide the reconstruction of maxillary anterior teeth with direct composite resin over self-threading dentin pins. As the mandibular remaining teeth were extremely worn, a tooth-supported overdenture was installed. A stabilization splint was also used to protect the restorations. This treatment was a less expensive alternative to full-mouth rehabilitation with positive esthetic and functional outcomes after 1.5 years of follow-up.

The effect of poly(methyl methacrylate) surface treatments on the adhesion of silicone-based resilient denture liners.

STATEMENT OF PROBLEM: Different surface treatment protocols of poly(methyl methacrylate) have been proposed to improve the adhesion of silicone-based resilient denture liners to poly(methyl methacrylate) surfaces. PURPOSE: The purpose of this study was to evaluate the effect of different poly(methyl methacrylate) surface treatments on the adhesion of silicone-based resilient denture liners. MATERIAL AND METHODS: Poly(methyl methacrylate) specimens were prepared and divided into 4 treatment groups: no treatment (control), methyl methacrylate for 180 seconds, acetone for 30 seconds, and ethyl acetate for 60 seconds. Poly(methyl methacrylate) disks (30.0 × 5.0 mm; n = 10) were evaluated regarding surface roughness and surface free energy. To evaluate tensile bond strength, the resilient material was applied between 2 treated poly(methyl methacrylate) bars (60.0 × 5.0 × 5.0 mm; n = 20 for each group) to form a 2-mm-thick layer. Data were analyzed by 1-way ANOVA and the Tukey honestly significant difference tests (α = .05). A Pearson correlation test verified the influence of surface properties on tensile bond strength. Failure type was assessed, and the poly(methyl methacrylate) surface treatment modifications were visualized with scanning electron microscopy. RESULTS: The surface roughness was increased (P < .05) by methyl methacrylate treatment. For the acetone and ethyl acetate groups, the surface free energy decreased (P < .05). The tensile bond strength was higher for the methyl methacrylate and ethyl acetate groups (P < .05). No correlation was found regarding surface properties and tensile bond strength. Specimens treated with acetone and methyl methacrylate presented a cleaner surface, whereas the ethyl acetate treatment produced a porous topography. CONCLUSION: The methyl methacrylate and ethyl acetate surface treatment protocols improved the adhesion of a silicone-based resilient denture liner to poly(methyl methacrylate).

Candida albicans biofilms and MMA surface treatment influence the adhesion of soft denture liners to PMMA resin.

The effect of Candida albicans biofilms and methyl methacrylate (MMA) pretreatment on the bond strength between soft denture liners and polymethyl methacrylate (PMMA) resin was analyzed. Specimens were prepared and randomly divided with respect to PMMA pretreatment, soft liner type (silicone-based or PMMA-based), and presence or absence of a C. albicans biofilm. Samples were composed of a soft denture liner bonded between two PMMA bars. Specimens (n = 10) were incubated to produce a C. albicans biofilm or stored in sterile PBS for 12 days. The tensile bond strength test was performed and failure type was determined using a stereomicroscope. Surface roughness (SR) and scanning electron microscopy (SEM) analysis were performed on denture liners (n = 8). Highest bond strength was observed in samples containing a silicone-based soft liner and stored in PBS, regardless of pretreatment (p < 0.01). Silicone-based specimens mostly underwent adhesive failures, while samples containing PMMA-based liners predominantly underwent cohesive failures. The silicone-based specimens SR decreased after 12 days of biofilm accumulation or PBS storage, while the SR of PMMA-based soft liners increased (p < 0.01). The PMMA-based soft liners surfaces presented sharp valleys and depressions, while silicone-based specimens surfaces exhibited more gentle features. In vitro exposure to C. albicans biofilms reduced the adhesion of denture liners to PMMA resin, and MMA pretreatment is recommended during relining procedures.

Efficacy of citric acid denture cleanser on the Candida albicans biofilm formed on poly(methyl methacrylate): effects on residual biofilm and recolonization process.

BACKGROUND: It is well known that the use of denture cleansers can reduce Candida albicans biofilm accumulation; however, the efficacy of citric acid denture cleansers is uncertain. In addition, the long-term efficacy of this denture cleanser is not well established, and their effect on residual biofilms is unknown. This in vitro study evaluated the efficacy of citric acid denture cleanser treatment on C. albicans biofilm recolonization on poly(methyl methacrylate) (PMMA) surface. METHODS: C. albicans biofilms were developed for 72 h on PMMA resin specimens (n = 168), which were randomly assigned to 1 of 3 cleansing treatments (CTs) overnight (8 h). CTs included purified water as a control (CTC) and two experimental groups that used either a 1:5 dilution of citric acid denture cleanser (CT5) or a 1:8 dilution of citric acid denture cleanser (CT8). Residual biofilms adhering to the specimens were collected and quantified at two time points: immediately after CTs (ICT) and after cleaning and residual biofilm recolonization (RT). Residual biofilms were analyzed by quantifying the viable cells (CFU/mL), and biofilm architecture was evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). Denture cleanser treatments and evaluation periods were considered study factors. Data were analyzed using two-way ANOVA and Tukey's Honestly Significant Difference (HSD) test (α = 0.05). RESULTS: Immediately after treatments, citric acid denture cleansing solutions (CT5 and CT8) reduced the number of viable cells as compared with the control (p < 0.01). However, after 48 h, both CT groups (CT5 and CT8) showed biofilm recolonization (p < 0.01). Residual biofilm recolonization was also detected by CLSM and SEM analysis, which revealed a higher biomass and average biofilm thickness for the CT8 group (p < 0.01). CONCLUSION: Citric acid denture cleansers can reduce C. albicans biofilm accumulation and cell viability. However, this CT did not prevent biofilm recolonization.

Influence of daily immersion in denture cleanser on multispecies biofilm.

OBJECTIVE: The aim of this study was to evaluate the effect of daily exposure to a denture cleanser on a multispecies biofilm. MATERIALS AND METHODS: Multispecies biofilms (five bacteria and Candida albicans) were developed for 64.5 h on acrylic resin specimens and randomized into control and experimental groups. In the experimental group, biofilms were immersed in denture cleanser for 3 min/day for seven consecutive days. In the control group, the biofilms were developed with no treatment for the same period. Biofilms from both groups were collected after 1, 4, and 7 days and analyzed for the number of microorganisms and polysaccharide concentrations. Scanning electron microscopy (SEM) and confocal microscopy (CLSM) analyses were performed. RESULTS: The total microorganism counts and bacterial populations were lower in the experimental group compared to the control group for all of the periods evaluated. However, the C. albicans counts continuously increased in all of the cleanser-exposed biofilms, with abundant hyphae forms on SEM and CLSM images. The polysaccharide concentration was significantly higher in the experimental group after 7 days. CONCLUSIONS: Daily exposure of a multispecies biofilm to a denture cleanser reduces the number of total microorganisms but favors C. albicans development. CLINICAL RELEVANCE: Daily use of denture cleanser is an effective method for controlling bacteria in biofilm, but it can potentially select C. albicans, an important etiological agent of oral candidosis.

Candida albicans biofilms and MMA surface treatment influence the adhesion of soft denture liners to PMMA resin

The effect of Candida albicans biofilms and methyl methacrylate (MMA) pretreatment on the bond strength between soft denture liners and polymethyl methacrylate (PMMA) resin was analyzed. Specimens were prepared and randomly divided with respect to PMMA pretreatment, soft liner type (silicone-based or PMMA-based), and presence or absence of a C. albicans biofilm. Samples were composed of a soft denture liner bonded between two PMMA bars. Specimens (n = 10) were incubated to produce a C. albicans biofilm or stored in sterile PBS for 12 days. The tensile bond strength test was performed and failure type was determined using a stereomicroscope. Surface roughness (SR) and scanning electron microscopy (SEM) analysis were performed on denture liners (n = 8). Highest bond strength was observed in samples containing a silicone-based soft liner and stored in PBS, regardless of pretreatment (p < 0.01). Silicone-based specimens mostly underwent adhesive failures, while samples containing PMMA-based liners predominantly underwent cohesive failures. The silicone-based specimens SR decreased after 12 days of biofilm accumulation or PBS storage, while the SR of PMMA-based soft liners increased (p < 0.01). The PMMA-based soft liners surfaces presented sharp valleys and depressions, while silicone-based specimens surfaces exhibited more gentle features. In vitro exposure to C. albicans biofilms reduced the adhesion of denture liners to PMMA resin, and MMA pretreatment is recommended during relining procedures.

Recolonization of mutans Streptococci after application of chlorhexidine gel.

Streptococcus mutans is specifically suppressed by intensive treatment with chlorhexidine gel, but the time for recolonization and the effect on other oral bacteria are not totally clear. In this study, recolonization of mutans streptococci was evaluated in nine healthy adult volunteers, who were highly colonized with this microorganism. Stimulated saliva was collected before (baseline) and at 1, 7, 14, 21 and 28 days after application of 1% chlorhexidine gel on volunteers' teeth for two consecutive days. On each day, the gel was applied using disposable trays for 3 x 5 min with intervals of 5 min between each application. Saliva was plated on blood agar to determine total microorganisms (TM); on mitis salivarius agar to determine total streptococci (TS) and on mitis salivarius agar plus bacitracin to determine mutans streptococci (MS). Chlorhexidine was capable of reducing the counts of MS and the proportion of MS with regard to total microorganisms (%MS/TM) (p<0.05), but these values did not differ statistically from baseline (p>0.05) after 14 days for MS and 21 days for %MS/TM. The counts of TM and TS and the proportion of MS to total streptococci did not differ statistically from baseline (p>0.05) after chlorhexidine treatment. The results suggest that the effect of chlorhexidine gel treatment on suppression of mutans streptococci is limited to less than a month in highly colonized individuals.